Ampertangid AC 6000A (Rogowski pritnstiip) max. juhe 170mm
Võta ühendust
Tellimused ja päringud
info@yeint.eeTehniline informatsioon ja projektid
Keio Kalm keio.kalm@yeint.eeKaal | 420 g |
---|---|
Mõõtühik | tk |
Tootekood | 412371 |
Osa number | FLUKE I6000FLEX-24 |
Kaubamärk | FLUKE |
Estonia
Tellimuse järgi
Fluke i6000sFlex vahelduvvoolumõõtur
i6000sflex on vahelduvvooluandur, mis kasutab Rogowski põhimõtet. Seda saab kasutada kuni 6000 A voolu mõõtmiseks, kui seda kasutatakse koos ostsilloskoopide, salvestajate või andmelogijatega. Paindlik ja kerge mõõtepea võimaldab kiiret ja lihtsat paigaldamist raskesti ligipääsetavates kohtades.
Fluke i6000sFlex AC Current Probe
Electrical Characteristics
Current ranges 60 A / 600 A / 6000 A AC rms
Output sensitivity (AC coupled) 50 mV /5 mV / 0.5 mV per A
Load impedance 100 kOhm minimum
Accuracy (at +25°C) ±1% of range (45 – 65 Hz)
Linearity (10% to 100% of range) ±0.2% of reading
Noise 8 mV AC rms (60 A)
2 mV AC rms (600/6000 A)
Frequency range 10 Hz to 50 kHz (-3 dB)
Phase error < ±1° (45 – 65 Hz)
±10° (at 20 kHz)
Position sensitivity (with cable > 25 mm from the coupling)
Position sensitivity: From 1% up to 3% of range with cable, depending on distance from the center (see figure left). Measurements closer than 25 mm from the coupling are typically greater than 3% of range.
External wire influence: 1% (-40 db) of external current >200 mm from head.
External field (with cable > 200 mm from the head) ±1% of range
Power supply 2 x AA MN 1500 LR6 alkaline
400 Hours, low battery indicator or dedicated ext power supply
Temperature coefficient ±0.08% of reading per ° C
Working voltage (see Safety Standards section) 600 V AC rms or DC
General Characteristics
Head cable length (double insulated) 610 mm (24 in) I6000s Flex-24
915 mm (36 in) I6000s Flex-36
Head cable diameter 14.3 mm
Head bend radius 38.1 mm
Cable length (head to electronics) 2 m
Output connection 0.5 m cable terminated with safety BNC connector
Supplied with 4 mm safety plug adaptor
Operating temperature range -20 to +90°C (head)
-20 to +85°C (electronics)
Storage temperature range -40 to +105°C (head)
-20 to +85°C (electronics)
Operating humidity 15% to 85% (non condensing)
Weight 180 g (head), 190 g (electronics)
Safety Standards
BS EN 61010 1: 2001
BS EN 61010 2-032: 2002
BS EN 61010 031: 2002
600 V rms, Category III, Pollution degree 2
EMC standards BS EN 61326: 1998 +A1, A2, and A3
Use of the probe on uninsulated conductors is limited to 600 V AC rms or DC and frequencies below 1 kHz
Fluke i6000sFlex vahelduvvoolumõõtur
i6000sflex on vahelduvvooluandur, mis kasutab Rogowski põhimõtet. Seda saab kasutada kuni 6000 A voolu mõõtmiseks, kui seda kasutatakse koos ostsilloskoopide, salvestajate või andmelogijatega. Paindlik ja kerge mõõtepea võimaldab kiiret ja lihtsat paigaldamist raskesti ligipääsetavates kohtades.
Fluke i6000sFlex AC Current Probe
Electrical Characteristics
Current ranges 60 A / 600 A / 6000 A AC rms
Output sensitivity (AC coupled) 50 mV /5 mV / 0.5 mV per A
Load impedance 100 kOhm minimum
Accuracy (at +25°C) ±1% of range (45 – 65 Hz)
Linearity (10% to 100% of range) ±0.2% of reading
Noise 8 mV AC rms (60 A)
2 mV AC rms (600/6000 A)
Frequency range 10 Hz to 50 kHz (-3 dB)
Phase error < ±1° (45 – 65 Hz)
±10° (at 20 kHz)
Position sensitivity (with cable > 25 mm from the coupling)
Position sensitivity: From 1% up to 3% of range with cable, depending on distance from the center (see figure left). Measurements closer than 25 mm from the coupling are typically greater than 3% of range.
External wire influence: 1% (-40 db) of external current >200 mm from head.
External field (with cable > 200 mm from the head) ±1% of range
Power supply 2 x AA MN 1500 LR6 alkaline
400 Hours, low battery indicator or dedicated ext power supply
Temperature coefficient ±0.08% of reading per ° C
Working voltage (see Safety Standards section) 600 V AC rms or DC
General Characteristics
Head cable length (double insulated) 610 mm (24 in) I6000s Flex-24
915 mm (36 in) I6000s Flex-36
Head cable diameter 14.3 mm
Head bend radius 38.1 mm
Cable length (head to electronics) 2 m
Output connection 0.5 m cable terminated with safety BNC connector
Supplied with 4 mm safety plug adaptor
Operating temperature range -20 to +90°C (head)
-20 to +85°C (electronics)
Storage temperature range -40 to +105°C (head)
-20 to +85°C (electronics)
Operating humidity 15% to 85% (non condensing)
Weight 180 g (head), 190 g (electronics)
Safety Standards
BS EN 61010 1: 2001
BS EN 61010 2-032: 2002
BS EN 61010 031: 2002
600 V rms, Category III, Pollution degree 2
EMC standards BS EN 61326: 1998 +A1, A2, and A3
Use of the probe on uninsulated conductors is limited to 600 V AC rms or DC and frequencies below 1 kHz