Tööstuslik LTE Wifi Ruuter: CAT6 2.4GHz, 2xLAN, 802.11b/g/n, -40°C-75°C, IP30

Mobile module 4G (LTE) – Cat 6 up to 300 Mbps, 3G – Up to 42 Mbps

Status Signal strength, SINR, RSRP, RSRQ, Bytes sent/received, connected band, carrier aggregation, IMSI, ICCID

SMS SMS status, SMS configuration, send/read SMS via HTTP POST/GET, Email to SMS, SMS to Email, SMS to HTTP, SMS to SMS, SMS auto reply

USSD Supports sending and reading Unstructured Supplementary Service Data messages

Black/Whiles list (planned) Operator black/white list

Multiple PDN Possibility to use different PDNs for multiple network access and services

Band management Band lock, Used band status display

APN Auto APN

Bridge mode Direct connection (bridge) between mobile ISP and device on LAN

WIRELESS

Wireless mode 802.11 b/g/n, 2x2 MIMO, Access Point (AP), Station (STA)

WiFi security WPA3-EAP, WPA3-SAE, WPA2-Enterprise-PEAP, WPA2-PSK, WEP; AES-CCMP, TKIP, Auto Cipher modes, client separation

ESSID ESSID stealth mode

Wireless Hotspot Captive portal (Hotspot), internal/external Radius server, SMS OTP, MAC auth, built in customizable landing page, walled garden

ETHERNET

WAN 1 x WAN port (can be configured as LAN) 10/100 Mbps, compliance with IEEE 802.3, IEEE 802.3u standards, supports auto MDI/MDIX crossover

LAN 1 x LAN ports, 10/100 Mbps, compliance with IEEE 802.3, IEEE 802.3u standards, supports auto MDI/MDIX crossover

NETWORK

Routing Static routes, Dynamic routes (planned)

Network protocols TCP, UDP, IPv4, IPv6, ICMP, NTP, DNS, HTTP, HTTPS, FTP (planned), SMTP, SSL v3, TLS, ARP, VRRP, PPP, PPPoE, UPNP, SSH, DHCP, Telnet client, SNMP (planned), MQTT (planned), Wake on LAN (WOL) (planned)

VoIP passthrough support H.323 and SIP-alg protocol NAT helpers, allowing proper routing of VoIP packets

Connection monitoring Ping Reboot, Wget reboot, Periodic Reboot, LCP and ICMP for link inspection

Firewall Port forwards, traffic rules, NAT rules, custom rules

DHCP Static and dynamic IP allocation, DHCP Relay, Relayd

QoS / Smart Queue Management (SQM) (planned) Traffic priority queuing by source/destination, service, protocol or port, WMM, 802.11e

DDNS (planned) Supported >25 service providers, others can be configured manually

Network backup Mobile, Wired and WiFi WAN options, each of which can be used as an automatic Failover

Load balancing Balance Internet traffic over multiple WAN connections

SSHFS (optional) Possibility to mount remote file system via SSH protocol (not available in standard FW)

SECURITY

Authetication Pre-shared key, digital certificates, X.509 certificates

Firewall Pre-configured firewall rules can be enabled via WebUI, unlimited firewall configuration via CLI; DMZ; NAT; NAT-T

Attack prevention DDOS prevention (SYN flood protection, SSH attack prevention, HTTP/HTTPS attack prevention), port scan prevention (SYN-FIN, SYN-RST, X-mas, NULL flags, FIN scan attacks)

VLAN Tag based VLAN separation

Mobile quota control Custom data limits for both SIM cards

WEB filter (planned) Blacklist for blocking out unwanted websites, Whitelist for specifying allowed sites only

Access control Flexible access control of TCP, UDP, ICMP packets, MAC address filter

VPN

OpenVPN Multiple clients and a server can run simultaneously, 12 encryption methods

OpenVPN Encryption DES-CBC, RC2-CBC, DES-EDE-CBC, DES-EDE3-CBC, DESX-CBC, BF-CBC, RC2-40-CBC, CAST5-CBC, RC2-64-CBC, AES-128-CBC, AES-192-CBC, AES-256-CBC

IPSec IKEv1, IKEv2, with 5 encryption methods for IPsec (DES, 3DES, AES128, AES192, AES256)

GRE GRE tunnel

PPTP, L2TP Client/Server instances can run simultaneously, L2TPv3 support (planned)

Stunnel (planned) Proxy designed to add TLS encryption functionality to existing clients and servers without any changes in the program’s code

DMVPN (planned) Method of building scalable IPsec VPNs

SSTP (planned) SSTP client instance support

ZeroTier ZeroTier VPN client support

WireGuard WireGuard VPN client and server support

MODBUS

MODBUS TCP SLAVE (PLANNED)

ID filtering Respond to one ID in range [1;255] or any

Allow remote access Allow access through WAN

Custom registers Modbus TCP custom register block, which allows to read/write to a file inside the router, and can be used to extend Modbus TCP slave functionality

MODBUS TCP MASTER (PLANNED)

Supported functions 01, 02, 03, 04, 05, 06, 15, 16

Supported data formats 8 bit: INT, UINT; 16 bit: INT, UINT (MSB or LSB first); 32 bit: float, INT, UINT (ABCD (big-endian), DCBA (little-endian), CDAB, BADC), HEX, ASCII

MQTT GATEWAY (PLANNED)

Gateway Allows sending commands and receiving data from Modbus Master trough MQTT broker

DATA TO SERVER (PLANNED)

Protocols HTTP(S), MQTT, Azure MQTT, Kinesis

MONITORING & MANAGEMENT

WEB UI HTTP/HTTPS, status, configuration, FW update, CLI, troubleshoot, event log, system log, kernel log

FOTA Firmware update from server, automatic notification

SSH SSH (v1, v2)

SMS SMS status, SMS configuration, send/read SMS via HTTP POST/GET

Call Reboot, Status, Mobile data on/off, Output on/off

MQTT (planned) MQTT Broker, MQTT publisher

SNMP (planned) SNMP (v1, v2, v3), SNMP trap

JSON-RPC Management API over HTTP/HTTPS

Modbus (planned) Modbus TCP status/control

RMS Teltonika Remote Management System (RMS)

IoT PLATFORMS

Clouds of things Allows monitoring of: Device data, Mobile data, Network info, Availability

ThingWorx Allows monitoring of: WAN Type, WAN IP, Mobile Operator Name, Mobile Signal Strength, Mobile Network Type

Cumulocity Allows monitoring of: Device Model, Revision and Serial Number, Mobile Cell ID, ICCID, IMEI, Connection Type, Operator, Signal Strength, WAN Type and IP

Azure IoT Hub Can send device IP, Number of bytes send/received, Mobile connection state, Network link state, IMEI, ICCID, Model, Manufacturer, Serial, Revision, IMSI, SIM State, PIN state, GSM signal, WCDMA RSCP, WCDMA EC/IO, LTE RSRP, LTE SINR, LTE RSRQ, CELL ID, Operator, Operator number, Connection type, Temperature, PIN count to Azure IoT Hub server

SYSTEM CHARACTERISTICS

CPU QCA9531, MIPS 24kc, 650 MHz

RAM 128 MB, DDR2

FLASH storage 16 MB, SPI Flash (optional up to 256 MB)

FIRMWARE / CONFIGURATION

WEB UI Update FW from file, check FW on server, configuration profiles, configuration backup

FOTA Update FW/configuration from server

RMS Update FW/configuration for multiple devices at once

Keep settings Update FW without losing current configuration

INPUT/OUTPUT

Configurable I/O 2 x Configurable digital Inputs/Outputs. Digital input 0 - 6 V detected as logic low, 8 - 30 V detected as logic high. Open collector output, max output 30 V, 300 mA

Events SMS, Email, RMS

POWER

Connector 4 pin industrial DC power socket

Input voltage range 9 - 30 VDC, reverse polarity protection, voltage surge/transient protection

Power consumption 10.5 W max

PHYSICAL INTERFACES (PORTS, LEDS, ANTENNAS, BUTTONS, SIM)

Ethernet 2 x RJ45 ports, 10/100 Mbps

I/Os 2 x Configurable digital Inputs/Outputs on 4 pin power connector

Status LEDs 2 x Mobile connection type, 3 x Mobile connection strength, 2 x Eth status, 1 x Power

SIM 1 x SIM slots (Mini SIM - 2FF), 1.8 V/3 V, external SIM holders

Antenna 2 x SMA for LTE, 2 x RP-SMA for WiFi

Power 1 x 4 pin DC connector

Reset Reboot/User default reset/Factory reset button

PHYSICAL SPECIFICATION

Casing material Aluminium housing with DIN rail mounting option

Dimensions (W x H x D) 100 x 30 x 85 mm

Weight 247 g

Mounting options DIN rail, flat surface placement

OPERATING ENVIRONMENT

Operating temperature -40 C to 75 C

Operating humidity 10 % to 90 % non-condensing